New DLP Design Product Announcements:
DLP-RF430BP RFID BoosterPack
December 2013: DLP Design, Inc. is pleased to announce the new DLP-RF430BP
BoosterPack based on Near Field Communications (NFC) and microcontroller devices from Texas Instruments.
The DLP-RF430BP is an add-on board designed to fit TI’s MCU LaunchPads and incorporates
the Texas Instruments RF430CL330H. Its primary purpose is to help aid in the development process by providing a working hardware/firmware
reference example for NFC operations. This BoosterPack demonstrates a secure, simplified pairing
process for Bluetooth® and Wi-Fi connections with the only dynamic NFC tag device designed
specifically for NFC connection handover and service-interface functions. The RF430CL330H can also be used for creating
smart poster applications that direct a smartphone to a URL.
The DLP-RF430BP BoosterPack is an add-on board designed to fit TI’s MCU LaunchPads. This product
allows the software application developer to get familiar with the functionalities of the RF430CL330H on
their Texas Instruments embedded microcontroller platform of choice without having to worry about
designing the antenna.
Download the DLP-RF430BP datasheet (Updated 05-16-2014).
DLP-7970ABP RFID BoosterPack
September 2013: DLP Design, Inc. is pleased to announce the new DLP-7970ABP
BoosterPack based on NFC/RFID and microcontroller devices from Texas Instruments.
The DLP-7970ABP is an add-on board designed to fit TI’s MCU LaunchPads that incorporates
DLP Design’s DLP-RFID2 RFID module. This BoosterPack allows the software application developer to get
familiar with the functionalities of the TRF7970A multi-protocol, fully-integrated, 13.56MHz RFID/NFC IC
on their Texas Instruments embedded microcontroller platform of choice without having to worry about
developing the RF section.
Download the DLP-7970ABP datasheet.
DLP-2232H-SF High-Speed FPGA Module
March 2013: DLP Design, Inc. is pleased to announce the new DLP-2232H-SF
high-speed FPGA module based on silicon from Microsemi/Actel and FTDI.
The DLP-2232H-SF module is a low-cost, compact prototyping tool that can be used for rapid proof of
concept or within educational environments. The module is based on the Microsemi SmartFusionTM
cSoC microcontroller-FPGA and Future Technology Devices International’s FT2232H dual-channel
high-speed USB IC. The DLP-2232H-SF provides both the beginner as well as the experienced
engineer with a rapid path to developing FPGA-based designs. When combined with the Libero™ SoC
and SoftConsole™ IDE tools from Microsemi, this module is more than sufficient for creating anything
from basic logical functions to a highly complex system controller.
The DLP-2232H-SF is fully compatible with the free Libero™ SoC and SoftConsole™ IDE tools from
Microsemi. Libero™ SoC is used to configure the ARM® Cortex™-M3 Microcontroller Subsystem (MSS)
and the FPGA fabric design. Libero™ supports HDL synthesis and simulation, implementation, timing
verification, device fitting and JTAG programming. SoftConsole™ is based on the Eclipse IDE and is
used to compile, download and debug the C/C++ source code that runs on the MSS.
Download the DLP-2232H-SF datasheet.
DLP-RFID2 HF (13.56MHz) RFID Reader Products
November 2012: DLP Design, Inc. is pleased to announce the new DLP-RFID2
and DLP-RFID2D HF RFID readers.
The DLP-RFID2 and DLP-RFID2D are low-cost, compact RFID products for reading from and writing to HF RFID transponder
tags via an internal or external antenna. They have the ability to both read and write data in addition to
reading the unique identifier (UID). All of the DLP-RFID2’s and RFID2D's electronics reside on a single, compact
PCB, and all operational power is taken from one 3.0- to 5.0-volt supply. An external antenna can be
connected to the DLP-RFID2 via a standard u.fl connector or IO pin/pads.
Download the DLP-RFID2 datasheet (Updated 5-14-2014).
CDM Uninstaller: Program for selectively
removing FTDI devices with specific VID and PID combinations. Read the
manual for more details.
MPROG: EEPROM mode-configuration program V3.5 (This is a
legacy utility and has been replaced by FT_Prog. MPROG supports the FT2xxBM/L, FT2xxR and FTDI's high-speed ICs.)
MPROG V3.5 User's Guide
FT_Prog: EEPROM programming utility for use with
FTDI devices. It is used to customize the EEPROM contents and can modify information such as device descriptors.
USBView Program: View the VID and PID of all connected USB
devices even without drivers loaded.
Current Versions of FTDI Drivers:
CDM (Combined Driver Model Version 2.8.30) Windows Drivers:
WHQL-certified USB drivers are required for 64-bit Windows 7 systems.
FTDI default VID/PID values (0403/6001 for single channel, 6010 and 6011 for dual) listed
in the .inf files must be programmed into EEPROM using MPROG or FT_PROG.
You can either download the WHQL certified driver files above or use the install executable to install them.
- Make sure the USB device is not plugged in.
- Download the FTDI driver install executable.
- Run the driver exe file.
- Wait for the command window to vanish.
- Plug in the USB device and the driver will load.
CDM (Combined Driver Model Version 2.8.14) Windows Drivers:
Modified .inf files for use with specific DLP Design products on XP/Vista/Windows 7 systems (DLP-TH1b, DLP-TILT, DLP-D-G, DLP-RFID1, DLP-UT1, DLP-UTH8).
See Note 1
Note 1: In order to use the listed DLP Design products on a 64-bit machine, the VID/PID
values in the EEPROM area must first be changed to the FTDI default of 0403/6001 (0403/6010 and 0403/6011 for dual-channel products) so that
the WHQL-certified drivers will load. Use the MPROG utility (above) on a non-64 bit (ex: XP) machine to update the values
in the EEPROM. You can also hold down F8 during boot on a 64-bit PC and disable the driver certification check so that the non-certified
drivers can be loaded and the PID changed using MPROG.
For more info: TN_129
Note 2: If an extra COM port is not available after installing the latest CDM driver, connect the USB device and open
Control Panel > System > Device Manager. Right click on USB Serial Converter under USB Controllers and select Properties, then
the Advanced tab. Check the box marked "Load VCP", then click OK. Unplug and re-plug the USB device, and the COM port will be
added. This method is also used to change the driver mode from VCP to D2XX (DLL).
More FTDI Drivers
FTDI App Notes